Sikafloor®-350 N Elastic
Sikafloor®-350 N Elastic is a two part, solvent free, highly elastic polyurethane resin.
- Very good crack-bridging ability even at low temperatures (down to -20°C)
- Mechanically resistant as a broadcast system
- Watertight
- Economical in use
- Solvent free
Usage
Sikafloor®-350 N Elastic is used for:- Highly elastic, crack-bridging, trafficable, slip resistant wearing layers
- Particularly suitable for car park decks, garage floors and bridges etc.
Advantages
- Very good crack-bridging ability even at low temperatures (down to -20°C)
- Mechanically resistant as a broadcast system
- Watertight
- Economical in use
- Solvent free
Packaging
| Part A | 9.0 kg containers |
| Part B | 21.0 kg containers |
Part A+B | 30.0 kg ready to mix units |
Colour
Pebble grey | |
Resin - part A: | light brown, liquid |
Hardener - part B: | transparent, liquid |
Product Details
ENVIRONMENTAL INFORMATION
LEED Rating:
Sikafloor®-350 N Elastic conforms to the requirements of LEED EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings
SCAQMD Method 304-91 VOC Content < 100 g/l
APPROVALS / STANDARDS
- Coating for concrete protection according to the requirements of EN 1504-2:2004 and the EN 13813:2002, DoP 0208010402500000011008 certified by Factory Production Control Body, 0921 and provided with the CE-mark.
- Certified as part of the Surface Protection System OS 11a according to DIN EN 1504-2 and DIN V 18026.
- Certified as part of the Surface Protection System OS 11b according to DIN EN 1504-2 and DIN V 18026.
- Reaction to Fire classification according to DIN EN 13501-1. Test institute Hoch Report No. KB-Hoch-101213 and MPA Dresden Report No. 2007-B-0181/8
Chemical Base
Polyurethane
Shelf Life
12 months from date of production
Storage Conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5°C and +30°C.
Density
Part A: | ~ 1.83 kg/l |
Part B: | ~ 1.02 kg/l |
Part A+B: | ~ 1.18 kg/l |
Density value at +23°C.
Solid content by weight
~100%
Solid content by volume
~100%
Shore A Hardness
~60 (14 days / +23°C) | (DIN 53505) |
Tensile Strength
| ~ 5.0 N/mm2 (14 days / +23°C) | (DIN 53504) |
Application
Mixing Ratio
Part A : part B = 30 : 70 (by weight)
Ambient Air Temperature
+10°C min. / +30°C max.
Relative Air Humidity
80% r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10°C min. / +30°C max.
Substrate Moisture Content
< 4% pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperatures | Time |
+10°C | ~ 60 minutes |
+20°C | ~ 30 minutes |
| +30°C | ~ 15 minutes |
Curing Time
Before overcoating Sikafloor®-350 N Elastic broadcast allow:
Substrate temperature | Minimum | Maximum |
+10°C | 24 hours | * |
+20°C | 15 hours | * |
+30°C | 8 hours | * |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
* No max. waiting time if fully broadcast surface is free from all contaminations.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10°C | ~ 24 hours | ~ 5 days | ~ 10 days |
+20°C | ~ 15 hours | ~ 3 days | ~ 7 days |
+30°C | ~ 8 hours | ~ 2 days | ~ 5 days |
Note: Times are approximate and will be affected by changing ambient conditions
Consumption
~ 1.2 kg/m2/mm. Please refer to the respective System Data Sheet
MIXING
Prior to mixing, stir part B mechanically. When all of part A has been added to part B, mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add the quartz sand 0.1 - 0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.
Mixing Tools:
Sikafloor®-350 N Elastic must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
APPLICATION
Sikafloor®-350 N Elastic is poured and spread evenly by means of a serrated/notched trowel. Then, level and remove entrained air with a spiked roller.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use.
Hardened and/or cured material can only be removed mechanically.