Sikafloor®-359 N
Polyurethane tough-elastic coloured seal coat
Sikafloor®-359 N is a two part tough-elastic, coloured, non-yellowing, polyurethane seal coat.
- Flexible and tough elastic
- Good mechanical resistance
- Good resistance to specific chemicals
- Impermeable to liquids
- Very good yellowing resistance
- Matt finish
Usage
The Product is used as a:- Seal coat or Top coat for slip resistant broadcast systems
Advantages
- Flexible and tough elastic
- Good mechanical resistance
- Good resistance to specific chemicals
- Impermeable to liquids
- Very good yellowing resistance
- Matt finish
Packaging
Container Part A | 25.35 kg |
Container Part B | 7.15 kg |
Container Part A + Part B | 32.5 kg |
Refer to the current price list for available packaging variations.
Colour
Part A | coloured, liquid |
Part B | transparent, liquid |
Cured appearance | Matt finish |
Cured colour | Almost unlimited choice of colour shades. |
Product Details
ENVIRONMENTAL INFORMATION
Contributes towards satisfying Materials and Resources (MR) Credit: Building product disclosure and optimization — Environmental Product Declarations under LEED® v4
Environmental Product Declaration (EPD) in accordance with EN 15804. EPD independently verified by Institut für Bauen und Umwelt e.V. (IBU)
APPROVALS / STANDARDS
-
CE marking and declaration of performance based on EN 13813:2002 Screed material and floor screeds — Screed material — Properties and requirements — Synthetic resin screed material
-
CE marking and declaration of performance based on EN 1504-2:2004 Products and systems for the protection and repair of concrete structures — Surface protection systems for concrete — Coating
Chemical Base
Polyurethane
Shelf Life
12 months from date of production
Storage Conditions
The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Refer to the current Safety Data Sheet for information on safe handling and storage.
Density
Part A | 1.67 kg/l |
Part B | 1.05 kg/l |
Mixed Product | 1.45 kg/l |
Solid content by weight
85 %
Solid content by volume
85 %
Shore D Hardness
Cured 7 days at 23 °C | 52 |
Abrasion Resistance
Cured 7 days at 23 °C | 160 mg |
Tensile Adhesion Strength
> 1.5 N/mm² (failure in concrete) | (EN 1542) |
Application
Mixing Ratio
Part A : Part B (by weight) | 78 : 22 |
Product Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Ambient Air Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Relative Air Humidity
Maximum | 80 % r.h. |
Dew Point
Beware of condensation. The substrate and uncured applied product must be at least +3 °C above dew point to reduce the risk of condensation on the surface of the applied product.
Substrate Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Substrate Moisture Content
Refer to the individual primer Product Data Sheet.
Pot Life
+10 °C | 40 minutes |
+20 °C | 25 minutes |
+30 °C | 15 minutes |
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | 48 hours | 5 days | 10 days |
+20 °C | 24 hours | 3 days | 7 days |
+30 °C | 16 hours | 2 days | 5 days |
Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.
Consumption
0.7–0.9 kg/m² per coat
0.7–0.9 kg/m² per coat |
SUBSTRATE QUALITY
IMPORTANT
Incorrect treatment of cracks
The incorrect assessment and treatment of cracks may lead to a reduced service life and reflective cracking.
TREATMENT OF JOINTS AND CRACKS
Construction joints and existing static surface cracks in substrate require pre-treating before full layer application. Use Sikadur® or Sikafloor® resins.
SUBSTRATE CONDITION
Cementitious substrates must be structurally sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum tensile strength of 1.5 N/mm2.
Substrates must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
SUBSTRATE PREPARATION
MECHANICAL SUBSTRATE PREPARATION
IMPORTANT
Exposing blow holes and voids
When mechanically preparing the surface, make sure to fully expose blow holes and voids.
- Remove weak cementitious substrates.
- Prepare cementitious substrates mechanically using abrasive blast cleaning or planing / scarifying equipment to remove cement laitance.
- Before applying thin layer resins, remove high spots by grinding.
- Use industrial vacuuming equipment to remove all dust, loose and friable material from the application surface before applying the Product.
- Use products from the Sikafloor®, Sikadur® and Sikagard® range of materials to level the surface or fill cracks, blow holes and voids.
Contact Sika® Technical Services for additional information on products for levelling and repairing defects.
SUBSTRATE PREPARATION OF NON-CEMENTITIOUS SUBSTRATES
For information on substrate preparation of non-cementitious substrates, contact Sika technical services.
MIXING
- Mix part A until a uniform colour and mix has been achieved.
- Add Part B (hardener) to Part A.
- IMPORTANT Do not mix excessively. Mix Part A + B continuously for ~3 minutes until a uniformly coloured mix is achieved.
- To ensure thorough mixing, pour materials into another container and mix again to achieve a smooth and uniform mix.
- During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
APPLICATION
IMPORTANT
Strictly follow installation procedures
Strictly follow installation procedures as defined in Method Statements, application manuals and working instructions which must always be adjusted to the actual site conditions.
IMPORTANT
Protect from moisture
After application, protect the Product from damp, condensation and direct water contact for at least 24 hours.
IMPORTANT
Temporary heating
If temporary heating is required, do not use gas, oil, paraffin or other fossil fuel heaters. These produce large quantities of both carbon dioxide and water vapour, which may adversely affect the finish.
- For heating, use only electric powered warm air blower systems.
Exact colour matching
Note: For exact colour matching, ensure the Product in each area is applied from the same control batch number.
SEAL COAT FOR BROADCAST SURFACES
-
Pour the mixed Product onto the substrate.
Note: The consumption is specified in Application Information. - Spread the Product evenly over the surface with a squeegee.
-
Back roll the surface in two directions at right angles with a fleece roller.
Note: Maintain a "wet edge" during application to achieve a seamless finish.
CLEANING OF TOOLS
Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically.
To prevent the nozzle from blocking, regularly clean the spraying equipment during application.