Sikafloor®-20 PurCem®
High strength, chemical and thermal shock resistant polyurethene hybrid trowel grade flooring screed with high slip resistance
Sikafloor®-20 PurCem® is a multi-component, water based colored polyurethane hybrid flooring screed. It has flat, high abrasion, chemical, impact and high slip-resistant finish.
- Good resistance to specific chemicals
- High mechanical resistance
- Non-tainting
- Odourless
- Thermal expansion properties similar to concrete
- Tolerant to substrates with high moisture content
Usage
The Product is used as a wearing layer and levelling screed for Sikafloor® PurCem® flooring systems. Please note:- The Product may only be used by experienced professionals.
Advantages
- Good resistance to specific chemicals
- High mechanical resistance
- Non-tainting
- Odourless
- Thermal expansion properties similar to concrete
- Tolerant to substrates with high moisture content
Packaging
Container Part A | 3 kg |
Container Part B | 3 kg |
Part C | 26.5 kg bag |
Packaging combined | 32.5 kg ready to mix units |
Refer to the current price list for available packaging variations.
Colour
Part A | Coloured liquid |
Part B | Brown liquid |
Part C | Natural grey powder |
Cured appearance | Matt finish |
Cured colour | Telegrey 1&2, Beige, Golden Yellow, Dusty Grey, Traffic Red, Oxide Red, Light Grey, Dark Grey, Sky Blue, Leaf Green |
Note: When the Product is exposed to direct sunlight, there may be some discolouration and colour variation. This has no influence on the function and performance of the Product.
For colour matching: Apply colour sample and confirm selected colour under real lighting conditions.
Product Details
ENVIRONMENTAL INFORMATION
-
Environmental Product Declaration (EPD) in accordance with EN 15804. EPD independently verified by Institut für Bauen und Umwelt e.V. (IBU)
-
VOC emissions AgBB, Sikafloor®-20 PurCem®, eurofins, Approval No. 392-2014-00087
-
VOC emission classification of building materials RTS M1
-
Conforms with LEED v4 EQ credit: Low-emitting materials
-
Conforms with LEED v4 MR credit: Building product disclosure and optimization — Environmental Product Declarations (option 1)
APPROVALS / STANDARDS
-
CE marking and declaration of performance based on EN 13813:2002 Screed material and floor screeds — Screed material — Properties and requirements — Synthetic resin screed material
-
Incidental food contact USD Regulations, Sikaflooor®-20 PurCem®, USDA, Certifica
-
Tainting test Sikafloor®-20 PurCem®, Campden, Report No. 125424/2
-
Cleaning test Sikafloor®-20 PurCem, CSM Fraunhofer, Certificate No. 1403-695
-
Water transmission test EN 1062-3, Sikafloor®-20 PurCem®, Technology Centre, Cer
-
Abrasion resistance test Sikafloor®-20 PurCem®/-21 PurCem®, Face consultants, Re
-
Impact resistance test Sikafloor®-20 PurCem®, PRA, Report No. 75221-151a
-
Fire testing EN 13501-1, APPLUS, No. 21/32303045-2
Chemical Base
Water-based polyurethane cement hybrid
Shelf Life
Part A | 12 months from date of production |
Part B | 12 months from date of production |
Part C | 9 months from date of production |
Always refer to the best before date of the individual packaging.
Storage Conditions
The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C.
Always refer to packaging.
Refer to the current Safety Data Sheet for information on safe handling and storage.
Density
Mixed Product | ~2.08 kg/l at +20 °C |
Shore D Hardness
Cured 7 days at +23 °C | 85 |
Compressive Strength
Cured 28 days at +23 °C | 50 N/mm² |
Tensile Strength in Flexure
Cured 28 days at +23 °C | 10 N/mm² |
Reaction to Fire
Class Bfl-s1 | (EN 13501-1) |
Application
Mixing Ratio
Part A : Part B : Part C | 3.0 : 3.0 : 26.5 |
Layer Thickness
Wear coat | 6-9 mm |
Levelling screed | 12-30 mm (where defined aggregates are added) |
Product Temperature
Sikafloor®-20 PurCem® | |
Minimum | +10 °C |
Maximum | +35 °C |
Ambient Air Temperature
Minimum | +10 °C |
Maximum | +35 °C |
Relative Air Humidity
Maximum | 80 % |
Dew Point
Beware of condensation. The substrate and uncured applied product must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product. Low temperatures and high humidity conditions increase the probability of blooming.
Substrate Temperature
Minimum | +10 °C |
Maximum | +35 °C |
Substrate Moisture Content
The Product can be installed on substrates with a higher moisture content. No ponding water may be present on the surface. Check for rising moisture. The substrate must be visibly dry and must have a minimum pull-off strength of 1.5 N/mm².
Pot Life
+10 °C | ~40 minutes |
+20 °C | ~25 minutes |
+30 °C | ~18 minutes |
+35 °C | ~15 minutes |
Waiting Time / Overcoating
Before overcoating the Product allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 24 hours | 72 hours |
+20 °C | 24 hours | 48 hours |
+30 °C | 12 hours | 24 hours |
+35 °C | 12 hours | 24 hours |
Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.
Note: If a primer other than a scratch coat of Sikafloor PurCem is applied, refer to the relevant PDS of the chosen product for curing times. Ensure that the primer or scratch coat is fully cured before the application of subsequent Sikafloor PurCem layers.
Consumption
~2.1 kg/m² per mm thickness
EQUIPMENT
MIXING EQUIPMENT
Electric single paddle mixer (300 to 400 rpm)
Electric double paddle mixer (>700 W, 300 to 400 rpm)
Forced action / rotating pan / double paddle or trough type mixer (300–400 rpm )
APPLICATION EQUIPMENT
Flat, round edge steel trowel
Short pile roller
MIXING
3 PART MIXING PROCEDURE
- Mix Part A (resin) for ~30 seconds.
- Add Part D (colour pack) to Part A.
- Mix Part A + B continuously for 30 seconds until a uniformly coloured mix is achieved.
- Pour the mixed resin Parts into the pan mixer.
- Start the pan mixer and gradually add Part C (aggregate) to the mixed resin Parts over a period of 15 seconds.
- After combining all parts, mix for an additional 2 minutes, until a uniform mix is achieved. Note: At ambient temperatures less than +15 °C mix between 30 seconds and 1 minute longer.
- During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
4 PART MIXING PROCEDURE
- Mix Part A (resin) for ~30 seconds.
- Add Part D (colour pack) to Part A.
- Mix Part A + D continuously for 30 seconds until a uniformly coloured mix is achieved.
- After mixing for 30 seconds, gradually add Part B and continue mixing for 30 seconds.
- Pour the mixed resin Parts into the pan mixer.
- Start the pan mixer and gradually add Part C (aggregate) to the mixed resin Parts over a period of 15 seconds.
- After combining all parts, mix for an additional 2 minutes, until a uniform mix is achieved. Note: At ambient temperatures less than +15 °C mix between 30 seconds and 1 minute longer.
- During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
APPLICATION
IMPORTANT
Protecting the material after application
After application, protect the System from damp, condensation and direct water contact for at least 24 hours.
IMPORTANT
Protect from overhead leaks and condensation
Protect the Product during application from pipe condensation or any overhead leaks.
IMPORTANT
Ventilation in confined spaces
Always ensure good ventilation when applying the Product in a confined space.
IMPORTANT
Application on polymer modified cement mortars
Do not apply the product on polymer modified cement mortars if the mortar expands when sealed with an impervious resin.
IMPORTANT
Waiting time for foodstuff
Allow a minimum of 48 hours after application before placing foodstuff in the same area.
RESIN SCREED
- Pour the mixed Product "wet on wet" onto the still tacky primer. Note: The consumption is specified in Application Information.
- Spread and compact the Product with a trowel to the required thickness between screed rails / battens, if installed.
- Level the screed surface with a levelling beam spanning onto the screed rails / battens.
- Finish the surface to the required surface texture with trowels or walk-behind power floats.
CLEANING OF TOOLS
Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically.