Sikafloor®-20 PurCem®

• Environmental Product Declaration (EPD) in accordance with EN 15804. EPD independently verified by Institut für Bauen und Umwelt e.V. (IBU)

• VOC emissions AgBB, Sikafloor®-20 PurCem®, eurofins, Approval No. 392-2014-00087

• VOC emission classification of building materials RTS M1

• Conforms with LEED v4 EQ credit: Low-emitting materials

• Conforms with LEED v4 MR credit: Building product disclosure and optimization — Environmental Product Declarations (option 1)

• CE marking and declaration of performance based on EN 13813:2002 Screed material and floor screeds — Screed material — Properties and requirements — Synthetic resin screed material

• Incidental food contact USD Regulations, Sikaflooor®-20 PurCem®, USDA, Certifica

• Tainting test Sikafloor®-20 PurCem®, Campden, Report No. 125424/2

• Cleaning test Sikafloor®-20 PurCem, CSM Fraunhofer, Certificate No. 1403-695

• Water transmission test EN 1062-3, Sikafloor®-20 PurCem®, Technology Centre, Cer

• Abrasion resistance test Sikafloor®-20 PurCem®/-21 PurCem®, Face consultants, Re

• Impact resistance test Sikafloor®-20 PurCem®, PRA, Report No. 75221-151a

• Fire testing EN 13501-1, APPLUS, No. 21/32303045-2

Water-based polyurethane cement hybrid

Always refer to the best before date of the individual packaging.

The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C.
Always refer to packaging.

Refer to the current Safety Data Sheet for information on safe handling and storage.

Beware of condensation. The substrate and uncured applied product must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product. Low temperatures and high humidity conditions increase the probability of blooming.

The Product can be installed on substrates with a higher moisture content. No ponding water may be present on the surface. Check for rising moisture. The substrate must be visibly dry and must have a minimum pull-off strength of 1.5 N/mm².

Before overcoating the Product allow:

Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

Note: If a primer other than a scratch coat of Sikafloor PurCem is applied, refer to the relevant PDS of the chosen product for curing times. Ensure that the primer or scratch coat is fully cured before the application of subsequent Sikafloor PurCem layers.

~2.1 kg/m² per mm thickness

MIXING EQUIPMENT

• Electric single paddle mixer (300 to 400 rpm)

• Electric double paddle mixer (>700 W, 300 to 400 rpm)

• Forced action / rotating pan / double paddle or trough type mixer (300–400 rpm )

APPLICATION EQUIPMENT

• Flat, round edge steel trowel

• Short pile roller

3 PART MIXING PROCEDURE

1. Mix Part A (resin) for ~30 seconds.
2. Add Part D (colour pack) to Part A.
3. Mix Part A + B continuously for 30 seconds until a uniformly coloured mix is achieved.
4. Pour the mixed resin Parts into the pan mixer.
5. Start the pan mixer and gradually add Part C (aggregate) to the mixed resin Parts over a period of 15 seconds.
6. After combining all parts, mix for an additional 2 minutes, until a uniform mix is achieved. Note: At ambient temperatures less than +15 °C mix between 30 seconds and 1 minute longer.
7. During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.

4 PART MIXING PROCEDURE

1. Mix Part A (resin) for ~30 seconds.
2. Add Part D (colour pack) to Part A.
3. Mix Part A + D continuously for 30 seconds until a uniformly coloured mix is achieved.
4. After mixing for 30 seconds, gradually add Part B and continue mixing for 30 seconds.
5. Pour the mixed resin Parts into the pan mixer.
6. Start the pan mixer and gradually add Part C (aggregate) to the mixed resin Parts over a period of 15 seconds.
7. After combining all parts, mix for an additional 2 minutes, until a uniform mix is achieved. Note: At ambient temperatures less than +15 °C mix between 30 seconds and 1 minute longer.
8. During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.

IMPORTANT

Protecting the material after application

After application, protect the System from damp, condensation and direct water contact for at least 24 hours.

IMPORTANT

Protect from overhead leaks and condensation

Protect the Product during application from pipe condensation or any overhead leaks.

IMPORTANT

Ventilation in confined spaces

Always ensure good ventilation when applying the Product in a confined space.

IMPORTANT

Application on polymer modified cement mortars

Do not apply the product on polymer modified cement mortars if the mortar expands when sealed with an impervious resin.

IMPORTANT

Waiting time for foodstuff

Allow a minimum of 48 hours after application before placing foodstuff in the same area.

RESIN SCREED

1. Pour the mixed Product "wet on wet" onto the still tacky primer. Note: The consumption is specified in Application Information.
2. Spread and compact the Product with a trowel to the required thickness between screed rails / battens, if installed.
3. Level the screed surface with a levelling beam spanning onto the screed rails / battens.
4. Finish the surface to the required surface texture with trowels or walk-behind power floats.

Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically.